DPA-100

Today we announce a brand new colorFabb material: DPA-100 – our first dissolvable support filament, specifically made for engineering materials.

colorFabb_XT and colorFabb PETG Economy printed with DPA-100. Topology optimized shelf bracket – by toms3dp

 

Learn more about the how-to and technical details here.

 

Beyond PVA

Unlike PVA our DPA-100 is less sensitive to moisture uptake and offers better shelf-life and print performance over time. It is a Dissolvable Polyacrylate material made to work specifically with engineering grade materials which are not suited for PVA, like PETG, ABS, ASA, PC and PA filaments. We have extensively tested DPA-100 on various 3D printing materials available in the market, both colorFabb and non-colorFabb branded.

DPA-100 is also perfectly suited for our range of co-polyester filaments: nGen, colorFabb_XT, colorFabb_HT and PETG Economy.

Quick guide: Which material and how?

Match Hotend temp Support Bed temp
nGen Yes 250 C 90C
colorFabb_XT Yes 250 C 90C
colorFabb_HT Yes 260 C 110C
PETG Economy Yes 250 C 90C
Generic ABS Yes 250C 100C
Generic ASA Yes 250C 100C

Read our full DPA-100 guide about the technical specifications and how to print.

 

Design by Ken Schulze

How to dissolve

Printing with DPA-100 is the first step. Dissolving the material is the second one. In order to dissolve DPA-100 you need a mild alkaline solution which is heated and stirred. At higher temperature DPA-100 will dissolve faster than at lower temperature. The temperature you choose depends on the temperature resistance of your build material. In general 20c below the temperature resistance of your build material is a safe settings. Thicker models would be less likely to deform and can handle temperatures closer to softening temperature. The minimum pH value for the alkaline solution is >10. We recommend using our DPA Detergent for making the alkaline solution.

The DPA Detergent is sold seperately from the DPA-100 filament.

 

Bicycle Helmet by Neomek

 

Detergent disclaimer

The detergent, dissolved in water, produces a mild alkaline which usually, together with the dissolved support material, can (in limited quantities) be disposed of via the wastewater. Please check your local regulations. You can acquire our waste profile datasheet by contacting support@colorfabb.com

Availability

DPA-100 and DPA detergent are available now exclusively from colorFabb’s website. Please note they are to be purchased separately.

DPA-100 is available as a 0.5kg spool and retails at € 120 ex VAT. Click here to head to our webshop.

DPA Detergent can be purchased per 1 kg drum at € 18 ex VAT and can be found here.

You can find all the relevant data sheets on the product pages.

 

How to print with DPA-100

What is DPA-100

DPA-100 is a dissolvable polyacrylate support material. A mild alkaline solution is needed to dissolve DPA-100 support material. Unlike PVA our DPA-100 is less sensitive to moisture uptake and offers better shelf-life and print performance over time.

Our DPA-100 support material is engineered to match with a variety of materials which can’t be supported by PVA due to bad adhesion to the build material. DPA-100 shows strong adhesion to PETG, ABS, ASA, PC and PA materials.

This means the DPA-100 is uniquely suited to match our co-polyester filament offering, nGen, colorFabb_XT, colorFabb_HT and PETG. DPA-100 is not recommended for use with PLA as build material due to the relatively high water temperature needed for dissolution.

colorFabb nGen supported by DPA-100 on the Ultimaker S5 – Bicycle Helmet by Neomek

How to Print with DPA-100

General settings

In order to successfully print with DPA-100 make sure your printer and slicer are able to set the below recommended settings.

Parameter DPA-100
Nozzle temperature 230-250C
Platform temperature 90-110C
Print speed 40-80 mm/s
Cooling fan 0% for best adhesion between layers
Standby nozzle temperature ~190C
Platform material PEI/BuildTak/Glass + adhesion promoter

Design by Ken Schulze

Avoid layer delamination – DPA-100

Make sure the printing temperature is high enough so you avoid the support structures from delaminating during the print. For most machines we would recommend  printing temperature of 240-260C, if your printer doesn’t feature a closed build chamber you would likely print at the higher range to avoid delamination of layers during the print.

If you do have a heated chamber, the temperature can be set to 70-90C. Without heated chamber the recommendation is to have the Platform temperature set to 90-110C.

Print a brim!

Use a brim around your model and support structures. If your slicer has the option select the build material to be used for printing the brim. This will help to keep the DPA-100 support structure in place. This is useful for thin and tall support beams to make sure these won’t tip over during the build. It also reduces warping of the DPA-100.

Design by Christopher Tenelsen

Solid support interface layer and 0 offset.

This might not be a surprise for most users, but make sure to enable the interface support layers and make these solid for the best surface quality on the build material. In our testing we also set the support structure offset to 0, to ensure best chance of good adhesion between support material and build material.

 

Which materials does DPA-100 support.

Match Hotend temp Support Bed temp
nGen Yes 250 C 90C
colorFabb_XT Yes 250 C 90C
colorFabb_HT Yes 260 C 110C
PETG Economy Yes 250 C 90C
Generic ABS Yes 250C 100C
Generic ASA Yes 250C 100C

Our DPA-100 support material is engineered to match with a variety of materials which can’t be supported by PVA due to bad adhesion to the build material. DPA-100 shows strong adhesion to PETG, ABS, ASA, PC and PA materials.

Prepare your prints

For a faster dissolving cycle try to remove as much support material before putting the model in the dissolving device. Wear eye protection and gloves when removing support material. If your model has fine detailed features do not try to attempt removing support material, you will risk damaging the model.

It’s good idea to keep note how much support material is removed so you know how much is going to be dissolved. Once the alkaline solution is saturated it can’t dissolve anymore support material and you will need to renew the alkaline solution.

colorFabb_XT to the left and colorFabb PETG Economy to the right. Topology optimized shelf bracket – by toms3dp

How to dissolve DPA-100

In order to dissolve DPA-100 you need a mild alkaline solution which is heated and stirred. At higher temperature DPA-100 will dissolve faster than at lower temperature. The temperature you choose depends on the temperature resistance of your build material. In general 20c below the temperature resistance of your build material is a safe settings. Thicker models would be less likely to deform and can handle temperatures closer to softening temperature. The minimum pH value for the alkaline solution is >10. We recommend using our DPA Detergent for making the alkaline solution.

At colorFabb we experimented with a low cost set-up for dissolving DPA-100. We used a sous-vide stick and a plastic containter with lid. The sous-vide stick will heatup the water to desired temp and circulate water.

 

The process step by step:

  • Fill up your dissolving device with water, use 4 l of water to dissolve 100 g of DPA deterent.
  • Heat the bath to the required temperature and start the recirculation process.
  • You can add your models as soon as the bath has reached the correct temperature and DPA detergent has been dissolved in water.
  • The dissolving process usually takes between an hour and 9 hours, depending on the amount of DPA-100 supportmaterial being dissolved, the geometry of the model and the temperature of the water. It’s a good idea to periodically check the process and if necessary change the position of the model in the device. Make sure the model is submerged for the duration of dissolving DPA-100 support material.
  • When the support material is full dissolved, let the model dry for at least 15 minutes, rotating the model a couple of times to make sure the detergent can drain off.
  • After initial drying, rinse the model thoroughly using warm, running water to remove the remaining detergent and then let dry completely.
  • After completely drying white residue could appear, if so, put the model into a warm (30 – 50 °C) water bath for at least one hour. Add rinsing agent for dish washers to speed up the process.
  • 1 kg of DPA-100 can dissolve at least 1 kg of support material. The more support material is dissolved, the slower the material will be able to dissolve. It’s a good idea to keep track of how many grams of support material has been dissolved so you know when to renew the alkaline solution.
  • Before disposing the solution, it must be neutralized. For this, we recommend 5 – 10 g citric acid per litre of used up solution. When foam formation occurs, the solution has reached a neutral pH area.
  • The detergent, dissolved in water, produces a mild alkaline which usually, together with the dissolved support material, can (in limited quantities) be disposed of via the wastewater. Please check your local regulations. You can acquire our waste profile datasheet by contacting support@colorfabb.com

For complete operating instruction on using DPA Detergent please click here.

Design by ISIFC